Part load position sensors (LPI)
On this page find you the electronic part load position sensors (LPI- Linear Position Indicator ) on refrigeration Screw compressors – The position of the slide valve will be given in 4-20 Ma signal direct to the PLC or additional a led system direct on the compressor – You can connect the partload indication direct on the the PLC or the most controllers – For question of availability contact us by E-mail.
RM-modification kits for Howden WRV models
![](https://interses.eu/wp-content/uploads/2023/02/RM-version.jpg)
Incase you like to read-0ut direct the position of the capacity slider valve, we offer the RM-modification kit for Howden WRV Compressors models- the power supply is 24 VDC and provide a out put of 4-20 mA. There are no led indication is steps of 10% only a direct output of 4-20mA. The benefit is that the read-out is always 1 valve. The Connection is hirschmann connection not a round connector as the Howden LPI sensor. – Note: the connection is different down load the calibration and connection instruction below.
For the WRV versions are on request also Atex LPI versions available
![RM-305 LPI Sensor on the Howden mk4/ WRV255/165.50](https://interses.eu/wp-content/uploads/2021/03/howden-lpi-modification-e1615403325813-150x150.png)
There are two suitable for the Howden Mk1 WRV 163 models in our program :
- RM-204 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
- Howden version for the WRV163
Howden MK2/WRV163 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system.
There are two suitable for the Howden Mk1- 6A/ WRV 204 models in our program :
- RM-305 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
- Howden version for the WRV204
Howden MK6B/WRV204 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
There are two suitable for the Howden Mk1- 6A/ WRV 255-110-130-165-193 models in our program :
- RM-305 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
- Howden version for the WRV255
The Howden model WRV255/220 longer and for this compressor is available:
- RM-405 modification kit.
- Howden version for the WRV255/220
Howden MK6B/WRV163 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
There are two suitable for the Howden Mk1-5 WRV 321 models in our program :
- RM-405 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
- Howden version for the WRV321
Howden MK6/WRV321 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system.
Print RM LPI
RM connection and calibration instruction
Linear positon indicator to indicate the position of the capacity slider Howden WRV compressor models
![](https://interses.eu/wp-content/uploads/2023/02/lpi-on-WRV-howden-300x266.png)
The Standard Howden linear Positon indicators are suited with a round connector and 10 led for each 10% load. The output is 4-20 mA . the power sypply 24 VDC. – Note: the connection is different down load the calibration and connection instruction below.
For the WRV versions are on request also Atex & Cullus versions available
![](https://interses.eu/wp-content/uploads/2023/02/LPI-WRVi-255-e1676906703928-300x234.png)
Print Howden LPI
Howden connection and Calibration instruction
On the Howden WRV163 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV163- M3001001
- For EXD area’s in ATEX version: HWLLCD-WRV163 -M3001001A
- For EXD area’s in CULUS version : HWLLCD-WRV163- M3001001C
On the Howden WRV204 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV204- M3001002
- For EXD area’s in ATEX version: HWLLCD-WRV204 -M3001002A
- For EXD area’s in CULUS version : HWLLCD-WRV204- M3001002C
On the Howden WRV255 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV255- M3001003
- For EXD area’s in ATEX version: HWLLCD-WRV255 -M3001003A
- For EXD area’s in CULUS version : HWLLCD-WRV255- M3001003C
On the Howden WRV321 models ( except the HowdenWRV321/220 model) is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV321- M3001004
- For EXD area’s in ATEX version: HWLLCD-WRV321 -M3001004A
- For EXD area’s in CULUS version : HWLLCD-WRV321- M3001004C
On the Howden WRV321/220 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV321/220- M3001004
- For EXD area’s in ATEX version: HWLLCD-WRV321/220 -M3001005A
- For EXD area’s in CULUS version : HWLLCD-WRV321/220- M3001005C
On the Howden WRV365 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV365- M3001007
- For EXD area’s in ATEX version: HWLLCD-WRV365 -M3001007A
- For EXD area’s in CULUS version : HWLLCD-WRV365- M3001007C
On the Howden WRV510 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-WRV510- M3001008
- For EXD area’s in ATEX version: HWLLCD-WRV510 -M3001008A
- For EXD area’s in CULUS version : HWLLCD-WRV510- M3001008C
Howden XRV models
The Linear position indicator for the Howden XRV models are also available in standard for non explosion proof area’s or in ATEX or CULUS version for explosion proof area’s- The supply power is 24 VDC and provide a out put of 4-20 mA and a 10 led indicationfor steps of 10% . – Note: the connection is different down load the calibration and connection instruction below
![](https://interses.eu/wp-content/uploads/2021/03/XRV-lpi.jpg)
Print Howden LPI
Howden connection and Calibration instruction
On the Howden XRV127 R1 model is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-XRV127- XR12000
- For EXD area’s in ATEX version: HWLLCD-XRV127 -XR12000A
- For EXD area’s in CULUS version : HWLLCD-XRV127- XR12000C
Howden MK1A/XRV127 R1 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
On the Howden XRV127 R3-5 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-XRV127- XR12000
- For EXD area’s in ATEX version: HWLLCD-XRV127 -XR12000A
- For EXD area’s in CULUS version : HWLLCD-XRV127- XR12000C
Howden MK1A/XRV127 R3-5 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
On the Howden XRV163 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-XRV163- XR16000
- For EXD area’s in ATEX version: HWLLCD-XRV163 -XR16000A
- For EXD area’s in CULUS version : HWLLCD-XRV163- XR16000C
Howden MK3B/XRV163 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
On the Howden XRV204 models is the following LPI models installed:
- for refrigeration & gases non explosive- area’s : HWLLCD-XRV204- XR24000
- For EXD area’s in ATEX version: HWLLCD-XRV204 -XR24000A
- For EXD area’s in CULUS version : HWLLCD-XRV204- XR24000C
Howden MK4B/WRV204 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
Howden XRV models modification kits
For Howden XRV models without a LPI we offer modification kits. The supply power is 24 VDC and provide a out put of 4-20 mA. – no led indicaton Note: the connection is different down load the calibration and connection instruction below
![](https://interses.eu/wp-content/uploads/2023/02/2-verspn-300x225.jpg)
Print RM LPI
RM connection and calibration instruction
modificaton kit for the Howden Mk1/XRV127 R1 model in our program :
- RM-204- xrv127 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
Howden MK1A/XRV127 R1 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
Modificaton kit for the Howden Mk1/XRV127 R3-5 models in our program :
- RM-204-XRV127 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
Howden MK1A/XRV127 R3-5 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
Modification kit for the Howden Mk1- 3A/ XRV163 models in our program :
- RM-305 XRV163 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
Howden MK3B/XRV163 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
Modification kit for the Howden Mk1-4A/ XRV204 models in our program :
- RM-305-XRV204 modification kit – Complete for modification from mechanical microswitches to electronically LPI output from 4-20 mA – without leds.
Howden MK4B/WRV204 models are standard suited with Howden LPI , except the compressor is on special order with micro switches.
With the RM- modification kit you can still upgrade to a electronic partload indication system
Sabroe Compressors
Find the correct model and LPI
![LPI SAB 128/163](https://interses.eu/wp-content/uploads/2021/03/Sab-128-e1615412927624-150x150.jpg)
- the SAB 110 S is suited with part 1553.298 for capacity indication
- the SAB110L is suited with part : 1553.295 for capacity indication
The SAB 128 can be suited with to types LPI :Part number :
- 3448.004 position indicator based on tuning principe
- 1553.288 positon indicator SAB 128 based linear position principe
The SAB 163 MK1-Mk2-MK3 can be suited with two types LPI :
Part number :
- 3448.004 position indicator based on tuning principe
- younger models are suited with part 1553.285 positon indicator based linear position principe
- The Sab 163 MK4 is suited with Part number: 1553-284 for capacity control
- the SAB163 mk4 is suited with part number 1553.285 for Vi indicaton
- The SAB 202S is suited with the LPI part number : 1372.296 for capacity indication and part number : 1373.301 for Vi indication.
- The SAB202L is suited with part number 1373.295 for capacity indication and part number : 1373.297 for Vi indicaton.
The SAB S24 – vertical compact compressor is suited with the LPI with the part number: 1553-284 for capacity indication
- the SAB 81 is suited with part 1553.273 for capacity indication
The SAB83 is suited with part: 1553.274 for capacity indicaton
The SAB 85 is suited with part 1553.275 for capacity indication.
- The SAB 87 is suited with the LPI part number : 1553.276 for capacity
The SAB 89 is suited with the LPI with the part number: 1553-277 for capacity indication
- The SAB 283 MK1 is suited with part 1373.057 for capacity indication.
- SAB283 mk1 is suited with part 1373.061 for Vi indication
GEA part load sensor part number: 627500015
These sensors are also available in ATEX and Culles version
![GEA capacity sensor part number 62700015](https://interses.eu/wp-content/uploads/2024/01/627500015-capacity-sensor-GEA-e1705167740270.png)
The sensor 627500015 details SW 25-2-0/3 4 …20 mA, IP65
The sensor 627500016 details SW 25-2-0/3 4 …20 mA, IP65 Tab only in EX version Culles
Stall Compressor
For the Stall S range are special part load set available
![](https://interses.eu/wp-content/uploads/2021/03/S73-lpi-150x150.png)
The S51-S54-S56-S57-S65-S71 Stall compressor models are suited with the LPI part number: 1556.123
The Stall models S67-S73-S75-S93 are suited with the LPI with the part number 1556.126
Gram Compressor
For the Gram compressor are the short stroke positon indicators available
![part load sensor Gram 52-021-0614](https://interses.eu/wp-content/uploads/2022/08/52-021-0614-300x129.png)
The Well know Gram short stroke capacity indicator part 52-021-0614 is available.
The sensor 52-021-0607 is replaced by part 534C1552H01
Aerzener VMY 256M Compressor
For the Aerzener VMY 256 M compressor are two versions capacity positon indicators available : Standard for NH3- Freon operation and a Atex version for inflammable refrigerants
![](https://interses.eu/wp-content/uploads/2024/05/Aerzener-VMY-256-capacity-postion-indicator-300x212.jpg)
The capacity indiactor with is suitable for NH3 and freon has our part number: 8160369177057.
The LPI sensor for application using a inflammable refrigerant , we can offer a Atex version.
The part number is for the Atex version : 8160368883539